Wikijunior Wie Dinge funktionieren/ Laser
Wenn Du an dieser Seite arbeiten möchtest, schenke bitte vorher den Autorenhinweisen kurz Deine Aufmerksamkeit. Danke!
A laser is a device that can produce a bright beam of colored light that is focused on a spot. Normally a light bulb glows white because it gives off light in every color we can see. It does so by heating up a strand of wire until it glows. The laser works very differently, so it can make a very narrow beam with only a single color. Laser is an acronym for Light Amplification by Stimulated Emission of Radiation
- 1 Who invented it?
- 2 How does it get power?
- 3 How does it work?
- 4 How dangerous is it?
- 5 What does it do?
- 6 How does it vary?
- 7 How has it changed the world?
- 8 What idea(s) and/or inventions had to be developed before it could be created?
Who invented it?[Bearbeiten]
The ideas that led to the invention of the laser were discovered by Albert Einstein in 1916. But it was not until 1953 that these ideas were put into use. The first laser was actually called a maser, because it used microwaves. (This is the same type of energy that is used in a microwave oven). Charles Townes and two of his students made the first maser, but it would only work for short amounts of time. Two scientists from the Soviet Union (Russia) named Nikolay Basov and Aleksandr Prokhorov figured out how to make the maser stay on. These three men won a Nobel Prize in 1964 for their discovery.
The first idea for a laser came from Charles Townes and Arthur Schawlow. Gordon Gould worked on the idea and wrote them down in a paper in 1959. This paper was the first time the word laser was used.
The first working laser was invented by Theodore Maiman and demonstrated on May 16, 1960.
How does it get power?[Bearbeiten]
A laser is powered by electricity. The electric current gives it the energy it needs to emit light.
How does it work?[Bearbeiten]
The name of the laser is an acronym that comes from first letters of the name, "Light Amplification by Stimulated Emission of Radiation". This is just a way of saying that a bright beam of light is created by pumping energy into a material. The energy radiation goes into the material from an outside source and pumps up or excites the material. The atoms in the material go into an excited/fast-moving state by absorbing this energy.
A single packet of light is called a photon. This word comes from the Greek name for light. When photon of a certain color passes an excited atom, it causes that atom to release a photon of the same color. So the total light becomes slightly brighter and the photons keep moving through the material. As it does so, it passes other excited atoms. These also emit photons of the same color. As a result the light is amplified/brightened, creating a bright laser beam of a single color.
The beam of light causes all the excited atoms to give off their energy as photons. Normally all the light would travel away until they are absorbed by a barrier. However if more energy is pumped into the material, it will keep the laser beam turned on.
A laser is made with a mirror at each end of the material. The light photons will bounce back and forth between these mirrors, causing more photons to be emitted.
(see discussion page about additions below)
Some lasers only have diodes.It is cut in half so you can see its parts. The picture below shows a laser diode,similar to light emitting diode.
The picture below shows a ruby laser.. The first working laser was a ruby laser, and it was invented in 1960.
It is cut in half so you can see its parts. The shiny red tube at the centre is a ruby crystal. That's where the laser beam will come from when the laser is switched on.
If you look closely at the picture, you will see that there are two round mirrors, one attached to each end of the ruby crystal. The mirror at the far end is called a "fully reflecting mirror". All the light reaching this type of mirror bounces back off it again.
The mirror at the near end of the crystal is called a "partially reflecting mirror". This type of mirror reflects most of the light, but some of the light can pass through it.
A tube made of quartz is coiled around the ruby crystal. It is called a "quartz flash tube", and each end of it is connected to a power supply, forming an electric circuit. In the picture above, we made the quartz flash tube see-through, so you can get a better view of the crystal.
All of these parts are inside an aluminium cylinder. The cylinder is highly polished, like a curved mirror.
Switching it on[Bearbeiten]
When the electric power supply is switched on, a current flows through the quartz flash tube, and it gives off a very bright burst of light. The reflecting cylinder around the flash tube helps to focus all that light onto the ruby crystal.
What happens inside the crystal?[Bearbeiten]
Like everything else, the ruby crystal is made of atoms. A real atom is so tiny, you can't see it, even with a very powerful microscope. They are much bigger in this picture so you can see them:
The light from the quartz flash tube hits the atoms in the crystal. Some of the atoms absorb the light, giving them more energy. They are said to be in a "higher energy level". To return to their previous energy level, they must get rid of the extra energy they got from the light. They do this by emitting a tiny particle of light called a "photon". Scientists call this process "stimulated emission of radiation" because the atoms are stimulated by the bright light, causing the emission of a photon of light, and light is a type of radiation. The next picture shows the atoms emitting photons.
Of course, in reality photons are a lot smaller than those in the picture. Photons are even smaller than the stuff that makes up atoms!
Where do the photons go?[Bearbeiten]
When they are emitted from the atoms, the photons of light shoot off in all directions.
Sometimes they pass close to another atom, and when that happens, the other atom might emit a photon too.
And if the photon from the other atom passes yet another atom, that atom might also emit a photon. So the number of photons increases very quickly, and the inside of the laser becomes very bright and hot. A water cooling system keeps it from overheating.
How is the laser beam formed?[Bearbeiten]
When the photons of light hit the mirrors, they are reflected back off them. Many of the photons will bounce back and forth between the mirrors, passing atoms on the way, and causing yet more photons to be emitted. Scientists call this "light amplification", because the light (made of photons) is amplified (made brighter).
With so many photons whizzing back and forth between the mirrors, many of them escape from the crystal through the partially reflective mirror at the front. We have shown some of these photons in the picture below.
The laser beam is made of many millions of these photons, escaping from the crystal through the front mirror.
The whole process, from flicking the switch to the laser beam appearing, happens in the blink of an eye.
How dangerous is it?[Bearbeiten]
The light from a laser beam can become very bright. If it has enough energy, this beam can cause damage to the eyes. You should not look directly into a laser beam. When scientists work with very powerful lasers, they must wear safety goggles over their eyes to avoid injury. Even a weak laser beam can damage the eyes when it is seen directly for a long time.
What does it do?[Bearbeiten]
A photon of light moves through space like a wave. Just like a wave moving across water, oscillating up and down, a light wave has a rate at which it vibrates. This rate is called the frequency, and it is the rate of vibration that determines the color we see.
A normal light bulb will emit many photons of light at various frequencies. As a result, we see the light from the bulb as white. A laser, however, only emits photons with a single frequency. Such light is called monochromatic, a word that means single color.
Much as a company of soldiers on parade all step at the same time, the photons from a laser are also moving in lock-step with each other. This is called coherence. It is a very useful property of a laser because of the way that waves interact with each other. It is this property of coherence, for example, that allows lasers to make holograms, which are pictures that can make a three-dimensional image.
Finally the light from a laser is all moving in the same direction. The light from a flashlight (British English: torch) comes out in a cone shape, and the brightness of the beam decreases the further away you get. But the tight beam from a laser will stay bright over much longer distances.
These three properties of a laser: monochromatic, coherence and a tight beam, are useful in many applications. Lasers are now being used in a great variety of devices. (See "How has it changed the world?" below for a list of examples.)
How does it vary?[Bearbeiten]
Lasers can differ from one another in the frequency of light they emit. The frequency depends on the types of materials used to make the laser. This is caused by differences in the properties of the atoms.
Lasers can also vary in the brightness, or intensity, of the beam of light they emit. The weakest lasers are fairly harmless and can be used in a classroom to point to locations on a projector screen. Some of the most powerful lasers can quickly cut through solid rock or metal sheets.
There are several different types of lasers. The material used to create the beam can be a solid, such as a piece of ruby. Some liquids and gasses can also be used to make a laser. Lasers can also be made out of similar materials as those used to make computer chips. Those are called semiconductor materials because of their electrical properties.
How has it changed the world?[Bearbeiten]
Lasers are very useful devices and they have been included in many devices. A material called optical fiber can be used to guide the light from a laser, and it is used to let computers talk to each other. Lasers are also used in CD and DVD drives to read the small pits on a disk.
Laser light travels in a very straight line. Straight beams of light can be used for measuring long distances and for keeping things lined up when building bridges and buildings. Soldiers use lasers to guide a rocket to a target.
Stronger lasers can be used to cut through hard metals. They are used for very fine surgery, such as fixing an eye that can not see well. They can be used to remove a tattoo or a birthmark.
What idea(s) and/or inventions had to be developed before it could be created?[Bearbeiten]
In order to create the laser, scientists had to explain how the atom worked. They had to come up with the theory called "quantum mechanics", which says that light and other very small particles all come in packets called quanta. This word comes from the Latin "quantum", which means how much.
The theory of quantum mechanics says that an atom can only store energy of certain amounts. Inside an atom are tiny negative particles called electrons that can absorb energy. When an electron receives just the right amount of energy, it can jump up to a higher level. By doing so it enters an excited state, which means it has more energy. Later the electron can release this energy, dropping back down to a lower, less excited state.